fw-rust: Initialize the LCD display
Send commands via SPI to the LCD display to initialize and configure it.
This commit is contained in:
parent
643e5f1af4
commit
817776d735
1 changed files with 30 additions and 3 deletions
|
@ -2,12 +2,18 @@
|
|||
#![no_main]
|
||||
|
||||
use atmega_hal::{
|
||||
clock::MHz8,
|
||||
delay::Delay,
|
||||
pins,
|
||||
spi::{DataOrder, SerialClockRate, Settings, Spi},
|
||||
Peripherals,
|
||||
};
|
||||
use avr_device::interrupt;
|
||||
use embedded_hal::spi::{Mode, Phase, Polarity};
|
||||
use embedded_hal::{
|
||||
blocking::delay::DelayMs,
|
||||
spi::{FullDuplex, Mode, Phase, Polarity},
|
||||
};
|
||||
use nb::block;
|
||||
use panic_halt as _;
|
||||
|
||||
#[atmega_hal::entry]
|
||||
|
@ -15,9 +21,10 @@ fn main() -> ! {
|
|||
// Disable interrupts when initializing
|
||||
interrupt::disable();
|
||||
|
||||
// Get peripherals and pins
|
||||
// Get peripherals, pins and delay
|
||||
let dp = Peripherals::take().unwrap();
|
||||
let pins = pins!(dp);
|
||||
let mut delay = Delay::<MHz8>::new();
|
||||
|
||||
// Init display backlight
|
||||
let tc0 = dp.TC0;
|
||||
|
@ -37,7 +44,7 @@ fn main() -> ! {
|
|||
pins.pd5.into_output();
|
||||
|
||||
// Init SPI
|
||||
let (_, _) = Spi::new(
|
||||
let (mut spi, _) = Spi::new(
|
||||
dp.SPI,
|
||||
pins.pb5.into_output(),
|
||||
pins.pb3.into_output(),
|
||||
|
@ -53,6 +60,26 @@ fn main() -> ! {
|
|||
},
|
||||
);
|
||||
|
||||
// Init LCD
|
||||
let _lcd_cd = pins.pb0.into_output();
|
||||
let mut lcd_rst = pins.pb1.into_output();
|
||||
// TODO: Test if delay is really needed
|
||||
delay.delay_ms(1_u8);
|
||||
lcd_rst.set_high();
|
||||
// TODO: Try to reduce delay to a minimum
|
||||
delay.delay_ms(5_u8);
|
||||
|
||||
block!(spi.send(0x40)).unwrap(); // (6) Set Scroll Line: Display start line 0
|
||||
block!(spi.send(0xA1)).unwrap(); // (13) Set SEG direction: SEG reverse
|
||||
block!(spi.send(0xC0)).unwrap(); // (14) Set COM direction: Normal COM0 - COM63
|
||||
block!(spi.send(0xA6)).unwrap(); // (11) Set Inverse Display: Display inverse off
|
||||
block!(spi.send(0xA2)).unwrap(); // (17) Set LCD Bias Ratio: Set Bias 1/9 (Duty 1/65)
|
||||
block!(spi.send(0x2F)).unwrap(); // (5) Set Power Control: Booster, Regulator and Follower on
|
||||
block!(spi.send(0x27)).unwrap(); // (8) Set VLCD Resistor Ratio: Set Contrast
|
||||
block!(spi.send(0x81)).unwrap(); // (9) Set Electronic Volume: Set Contrast
|
||||
block!(spi.send(0x08)).unwrap(); // (9) Set Electronic Volume: Set Contrast // TODO: Use EEPROM
|
||||
block!(spi.send(0xAF)).unwrap(); // (12) Set Display Enable: Display on
|
||||
|
||||
// Enable interrupts
|
||||
unsafe { interrupt::enable() };
|
||||
|
||||
|
|
Loading…
Reference in a new issue